AUTONET TV

Some New Boots (Suspension Maintenance)

There are some boots that don't come in a shoe box and aren't worn on your feet.  They are called axle or CV boots, and they can be important parts for many vehicles.

That CV stands for constant velocity.  CV axles are mainly used in front-wheel drive and all-wheel drive vehicles. They're also used in some rear-wheel drive vehicles with independent suspensions.  They have two CV joints, one inner and one outer, placed between the axle and the drive wheels.  That way the vehicle's engine power can drive the wheels, no matter what angle they are.  They also adjust for the different speeds wheels turn as they go around corners. 

Because roads are full of all sorts of hazards (dirt, oil, water, grime), these CV joints need to be protected.  They also have grease in them to keep the bearings moving smoothly.  That's the job of the rubber boots that are supposed to keep that debris out.  These CV or axle boots are made of rubber or plastic and usually last a long time without any problem.  But sometimes they fail, either from being hit by debris or age causing the rubber or plastic to deteriorate.  That can allow the grease to leak out of the joint and the moisture to get in.  And that's where the trouble is.

So it's important to have a vehicle's CV boots checked periodically, especially when they begin to have more than 100,000 miles/160,000 kilometers on them.  A technician inspects them for tears or cracks.  Sometimes if the problems are found early enough, the boots can be replaced and the joints can be re-packed with grease. 

But sometimes the CV joint can wear out even though the boot is intact.  When the CV joint fails, you might hear a grinding, humming or clicking noise and feel vibration.

Some of these can be difficult to access for service, so many service advisors will recommend replacing the joints and boots at the same time.  Just remember, new CV boots won't make a fashion statement, but they will keep your vehicle going down the road for years to come.

Bauer Auto Service
14455 State Hwy 23
Cold Spring, MN 56320
320-685-8846

Got it Covered! (Timing Cover Maintenance)

You may have heard at one time or another about something called a timing belt or timing chain in your engine.  And you may know that if they fail… well, let's just say that there can be some major engine damage.  So obviously, we want our timing belts and chains to be in tip-top shape.

One part that helps keep them running the way they should is the timing cover.  As you can probably guess, it's something that covers the belt or chain.  The timing cover protects both belts and chains from dirt and road debris.  Timing belts also need to be lubricated so their covers allow them to be lubricated as well.  They have a gasket that insures a good seal for the engine.  If that gasket breaks or develops a leak, then engine oil can escape, and loss of lubrication is never good for an engine component.

Other symptoms of a failed timing cover are leaking coolant, a metallic sound coming from the front of your engine or your Check Engine light coming on.  You might also notice a drop in power when you're going uphill.

It's important that your timing cover be in good condition and functioning properly.  Your repair facility will check out that part of your engine to make sure gaskets are in good shape and the cover is doing the job it's meant to do.  Catch that leaking or broken timing cover in time and your engine will thank you for avoiding some serious damage and an expensive repair.

Bauer Auto Service
14455 State Hwy 23
Cold Spring, MN 56320
320-685-8846

Such a Little Part (Climate Control Resistor)

You expect your heater/air conditioner to work like it should.  You have a control for temperature and one for fan speed.  You even have a control for what vents the air comes out of. 

Don't be surprised one day if your blower fan develops a mind of its own and starts going crazy.  Most of the time, you may find that it starts blowing at full speed, and nothing you do to try to control it does any good.  This is what may be happening.

Your blower motor has an electronic component called a resistor.  It does what its name says; it offers resistance.  When you want the fan to run more slowly, you turn the fan speed down.  That resistor accomplishes that by turning its resistance up.  When the resistor fails, the power has nothing to slow it and the fan speeds up. 

It's a small part and can fail due to age or corrosion.  It's usually not an expensive part, either, but it's often found in a location that's not that easy for the technician to get to.  That means labor costs will vary depending on the design of your vehicle. 

Occasionally, a faulty resistor can cause the blower motor not to work at all or only partially come on.  But other things can cause that as well, such as a faulty fan switch or vent control. 

This is where a technician's training comes in.  Special equipment can track down precisely where the issue is so you can be assured the correct part is being replaced.

It's just not pleasant when the blower motor isn't following orders.  Have your service facility check it out so you can be the blower's boss, like it should be. 

Bauer Auto Service
14455 State Hwy 23
Cold Spring, MN 56320
320-685-8846

It Wears on You (Tire Rotation)

If someone told you there was a fairly inexpensive way to improve your vehicle's handling, fuel economy and extend the life of your tires, you'd probably ask, "What do I have to do?" The answer is to rotate your tires.  But you have to do it regularly.

A lot of drivers think skipping tire rotation is a way to save money.  But when you don't rotate your tires, they will almost certainly wear unevenly.  That's because when your tires touch the surface of the road, the friction and traction causes miniscule parts of the rubber to come off.  And that process isn't exactly the same on each corner of your vehicle.  Some vehicles have the drive wheels in the front, some in the rear and some on all wheels.

Rotating your tires at regular intervals minimizes the differences in the way the tires wear.  The amount and pattern will be spread out equally if your tires spend time at all different positions.  The more even the wear, the more consistent traction, handling and braking will be.  All four tires will last longer this way, and when it is time to replace your tires, they'll all be worn out the same so you can replace all four with the same model tire.

Some people who choose not to rotate their tires find that one or two will wear much faster than the others, and often they'll replace just the worn ones.  While you can find similar tires, they won't all be the same and will certainly not have the same amount of wear. 

There are different tire rotation patterns depending on several factors: front-wheel drive, rear-wheel drive, all-wheel drive, directional tires/wheels, different sized wheels/tires on front and rear axles.  Also keep in mind that when your tires are new, some tire manufacturers require you to rotate them or else they won't honor the warranty. 

Your manufacturer recommends intervals for tire rotation, so it's best to follow their suggestion.  Your vehicle service facility can advise you when you need to get your tires rotated.  And many facilities include free tire rotation for as long as they're on your vehicle if you buy your tires at their shop.

Bauer Auto Service
14455 State Hwy 23
Cold Spring, MN 56320
320-685-8846

Getting from E to F (Fuel Gauge Problems)

Who thinks about their fuel gauge?  You probably don't… until it doesn't work any more.  Then you have to guess how much fuel is in your tank, and that's no way to live life on the road. 

Fuel gauges, like every other part in your vehicle, can fail.  And when yours stops working, you will probably want to head over to your service facility soon, because no one relishes running out of fuel.

The fuel gauge system is much more than just the gauge you can see on your instrument panel. Most systems have a float inside the fuel tank that goes up and down depending on the fuel level.  It's called the fuel sending unit, and it sends an electrical signal to the gauge (on the dash) telling it to display how much fuel is left in the tank. 

So, what could go wrong?  Well, a few things.  For one thing, corrosion from bad fuel can cause it to stick and it won't move up and down any more.  So you could fill up your tank and the gauge would still read Empty.  If a sending unit needs to be replaced, often the parts can be costly. The good news is that fuel sending units rarely fail and most drivers will never have one go bad.

Other things that can go wrong? An electrical problem could cause a fuse to blow and you won't get a reading at all.  A technician can figure out where that electrical problem is and how to repair it.  Finally, it's possible for the gauge itself (on the instrument panel) to fail.

One thing to keep in mind is if your fuel gauge isn't working, you might be tempted to carry around an extra container of fuel.  That's ok if it's outside the cabin, such as in the bed of a pickup.  But if you carry it inside the cabin or trunk, fuel fumes can be very dangerous for your health, even fatal.

A working fuel gauge gives you peace of mind… so you'll never have that "empty" feeling.

Bauer Auto Service
14455 State Hwy 23
Cold Spring, MN 56320
320-685-8846